Ultra Clear TP ED UV UF TM
€7.627,00
Catalog nr.: W3T276074
Menge
Ultra Clear TP ED UV UF TM - 2 l/min, Ultra pure water, Ultra filtration
The Ultra Clear™ TP ED series comes with an electronic dispenser (ED) allowing precise and volume-controlled dispensing of your ultra pure water for flows up to 2 l/min.
The software is intuitive and makes dispensing easy without any delay. A printer and Modbus interface integrates the data transfer into your existing system.
THE POLISHER MODELS
Designed for deionized water feed at conductivity
< 20 µS/cm. The unit has an ultrapure water output capacity up to 2 l/min and delivers a water quality of 18.2 MΩ-cm (0.055 µS/cm). The water produced exceeds current quality standards.
Wall mounted or bench system with TOC monitoring producing ultrapure pyrogen free water with a conductivity of 18.2 MOhm.cm (0.055 µS/cm) and TOC < 1-5 ppb, from a pre-treated (deionized or reverse osmosis) water source.
The unit consists of:
Ultrapure water production
1 pressure regulating valve
1 inlet solenoid valve to interrupt water feed when ultrapure water is not being withdrawn
1 flow turbine to recognize the volume dispensed
1 pre-treatment module DTO, pressure resistant and filled with high quality mixed bed resin and activated carbon
1 temperature compensated, inlet water conductivity sensor (SS 316 TI, C=0.2)
1 recirculation pump, (automatic speed reduction when water is not being dispensed
1 UV oxidation lamp 254/185 nm. The UV lamp is surrounded by high quality quartz glass for TOC reduction, and disinfection.
1 temperature compensated, conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC), TOC monitoring
1 polishing module MFIIID, filled with high quality synthetic activated carbon, mixed bed resin in semiconductor quality and adsorbed resin
1 ultra-filtration module Preventor 5000 with hollow fiber polysulphon membrane for pyrogen, RNase, DNase and colloid removal
1 temperature sensor, compensated (at 25°C in 0.1°C increments)
1 solenoid valve for module rinsing and temperature control
1 temperature compensated conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC)
1 Electronical dispenser PVDF, dead leg free, fully integrated in the recirculation loop and electronic recognition when in standby mode
1 0.2µm point-of-use filter with PES-membrane
1 volumetric ultrapure water dispenser
1 disinfection connection with quick fit couplers.
1 single dose of disinfection solution
1 connection kit, including 2m tube
Control panel:
Graphical and programmable 7''-touch-glass panel to display:
- flow diagram for quality parameter monitoring
- pure water conductivity after the pre-treatment module DTO
- conductivity/resistivity of the ultrapure water
- conductivity of TOC sample measurements,1-10 ppb measurement range
- ultrapure water temperature (temperature compensation can be disabled according to USP)
- servicing and consumable replacement requirements
- notification of system malfunction and/or quality issues
- settings monitoring
- 24-hour interval setting, prolonging pump and UV-lamp lifespan
- time program for automatic rinsing of the ultrafiltration module
- adjustable data backup to store conductivity, tank volume, pressure, and temperature data
- USB connection for data analysis
- micro-SD card for data backup (detachable)
- language options: German, English, French, Spanish, Portuguese and Chinese
- Managing entire unit using the control panel
- semi-automatic, menu selectable, disinfection of all water carrying parts
- setting of conductivity and temperature limits
- automatic disposal of recirculating water when the preset temperature limit is exceeded
- part number and consumables description within the control panel
- Easy cartridge replacement with user friendly connections
- cartridges with extended life-time
- Interface to connect POS printer or ModBus TCP/IP Data Communication Gateway to transfer the system status information to Building Management System (BMS)
The ultrapure laboratory water system is ready for use incl. the first set of modules and filters.
Technical data:
Ultrapure water specifications:
Volume flow rate: up to 2,0 l/min
Conductivity: 0.055 µS/cm
Resistivity: 18.2 MOhm-cm
TOC: < 1-5 ppb
Bacteria: < 1 CFU/ml
Silicate : < 1 ppb
Particulates > 0.1 µm/ml: < 1
Endotoxines : < 0.001 EU/ml
DNase, RNase, DNA: free
Feed water requirements:
Pressure: 0.1 - 5 bar
Feed Water Flow rate: 60-120 l/h
Conductivity: < 20 µS/cm
Free chlorine: < 0,1 mg/l
TOC: < 50 ppb
CO2: < 15 mg/l
SiO2: < 10 mg/l
Temperature: 5 - 35ºC
Mains input: 100-240 V, 50-60 Hz
Power consumption: 0,225 kW
Noise pressure level: max. 55 dB
Electrical connection cable
(D, GB, US): 2 m
Water connection: 1/2'' or 3/4'' female thread
Drain tube: 1/4''
Dimensions and Weight (System)
Width: 340 mm
Height: 535 mm
Depth: 550 mm
Dispatch weight: 26 kg
The Ultra Clear™ TP ED series comes with an electronic dispenser (ED) allowing precise and volume-controlled dispensing of your ultra pure water for flows up to 2 l/min.
The software is intuitive and makes dispensing easy without any delay. A printer and Modbus interface integrates the data transfer into your existing system.
THE POLISHER MODELS
Designed for deionized water feed at conductivity
< 20 µS/cm. The unit has an ultrapure water output capacity up to 2 l/min and delivers a water quality of 18.2 MΩ-cm (0.055 µS/cm). The water produced exceeds current quality standards.
Wall mounted or bench system with TOC monitoring producing ultrapure pyrogen free water with a conductivity of 18.2 MOhm.cm (0.055 µS/cm) and TOC < 1-5 ppb, from a pre-treated (deionized or reverse osmosis) water source.
The unit consists of:
Ultrapure water production
1 pressure regulating valve
1 inlet solenoid valve to interrupt water feed when ultrapure water is not being withdrawn
1 flow turbine to recognize the volume dispensed
1 pre-treatment module DTO, pressure resistant and filled with high quality mixed bed resin and activated carbon
1 temperature compensated, inlet water conductivity sensor (SS 316 TI, C=0.2)
1 recirculation pump, (automatic speed reduction when water is not being dispensed
1 UV oxidation lamp 254/185 nm. The UV lamp is surrounded by high quality quartz glass for TOC reduction, and disinfection.
1 temperature compensated, conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC), TOC monitoring
1 polishing module MFIIID, filled with high quality synthetic activated carbon, mixed bed resin in semiconductor quality and adsorbed resin
1 ultra-filtration module Preventor 5000 with hollow fiber polysulphon membrane for pyrogen, RNase, DNase and colloid removal
1 temperature sensor, compensated (at 25°C in 0.1°C increments)
1 solenoid valve for module rinsing and temperature control
1 temperature compensated conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC)
1 Electronical dispenser PVDF, dead leg free, fully integrated in the recirculation loop and electronic recognition when in standby mode
1 0.2µm point-of-use filter with PES-membrane
1 volumetric ultrapure water dispenser
1 disinfection connection with quick fit couplers.
1 single dose of disinfection solution
1 connection kit, including 2m tube
Control panel:
Graphical and programmable 7''-touch-glass panel to display:
- flow diagram for quality parameter monitoring
- pure water conductivity after the pre-treatment module DTO
- conductivity/resistivity of the ultrapure water
- conductivity of TOC sample measurements,1-10 ppb measurement range
- ultrapure water temperature (temperature compensation can be disabled according to USP)
- servicing and consumable replacement requirements
- notification of system malfunction and/or quality issues
- settings monitoring
- 24-hour interval setting, prolonging pump and UV-lamp lifespan
- time program for automatic rinsing of the ultrafiltration module
- adjustable data backup to store conductivity, tank volume, pressure, and temperature data
- USB connection for data analysis
- micro-SD card for data backup (detachable)
- language options: German, English, French, Spanish, Portuguese and Chinese
- Managing entire unit using the control panel
- semi-automatic, menu selectable, disinfection of all water carrying parts
- setting of conductivity and temperature limits
- automatic disposal of recirculating water when the preset temperature limit is exceeded
- part number and consumables description within the control panel
- Easy cartridge replacement with user friendly connections
- cartridges with extended life-time
- Interface to connect POS printer or ModBus TCP/IP Data Communication Gateway to transfer the system status information to Building Management System (BMS)
The ultrapure laboratory water system is ready for use incl. the first set of modules and filters.
Technical data:
Ultrapure water specifications:
Volume flow rate: up to 2,0 l/min
Conductivity: 0.055 µS/cm
Resistivity: 18.2 MOhm-cm
TOC: < 1-5 ppb
Bacteria: < 1 CFU/ml
Silicate : < 1 ppb
Particulates > 0.1 µm/ml: < 1
Endotoxines : < 0.001 EU/ml
DNase, RNase, DNA: free
Feed water requirements:
Pressure: 0.1 - 5 bar
Feed Water Flow rate: 60-120 l/h
Conductivity: < 20 µS/cm
Free chlorine: < 0,1 mg/l
TOC: < 50 ppb
CO2: < 15 mg/l
SiO2: < 10 mg/l
Temperature: 5 - 35ºC
Mains input: 100-240 V, 50-60 Hz
Power consumption: 0,225 kW
Noise pressure level: max. 55 dB
Electrical connection cable
(D, GB, US): 2 m
Water connection: 1/2'' or 3/4'' female thread
Drain tube: 1/4''
Dimensions and Weight (System)
Width: 340 mm
Height: 535 mm
Depth: 550 mm
Dispatch weight: 26 kg
Ultra Clear TP ED UV UF TM
1 piece
€7.627,00