Description
The Ultra Clear™ TP ED series comes with an electronic dispenser allowing precise and volume-controlled dispensing of your ultra pure water for
flows up to 2 l/min. The software is intuitive and makes dispensing easy without any delay.
A printer and Modbus interface integrates the data transfer into your existing system.
THE POLISHER MODELS
Designed for deionized water feed at conductivity
< 20 µS/cm. The unit has an ultrapure water output capacity up to 2 l/min and delivers a water quality of 18.2 MΩ-cm (0.055 µS/cm). The water produced exceeds current quality standards.
Wall mounted or bench system with TOC monitoring producing ultrapure water with a conductivity of 18.2 MOhm.cm (0.055 µS/cm) and TOC < 3 ppb, from a pre-treated (deionized or reverse osmosis) water source.
The unit consists of:
Ultrapure water production
1 pressure regulating valve
1 inlet solenoid valve to interrupt water feed when ultrapure water is not being withdrawn
1 flow turbine to recognize the volume dispensed
1 pre-treatment module DTO, pressure resistant and filled with high quality mixed bed resin and activated carbon
1 temperature compensated, inlet water conductivity sensor (SS 316 TI, C=0.2)
1 recirculation pump, (automatic speed reduction when water is not being dispensed
1 UV oxidation lamp 254/185 nm. The UV lamp is surrounded by high quality quartz glass for TOC reduction, and disinfection.
1 temperature compensated, conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC), TOC monitoring
1 polishing module MFIIID, filled with high quality synthetic activated carbon, mixed bed resin in semiconductor quality and adsorbed resin
1 temperature sensor, compensated (at 25°C in 0.1°C increments)
1 solenoid valve for module rinsing and temperature control
1 temperature compensated conductivity sensor (SS 316 TI, cell constant C=0.1, 0.1º intervals at 25ºC)
1 Electronical dispenser PVDF, dead leg free, fully integrated in the recirculation loop and electronic recognition when in standby mode
1 0.2µm point-of-use filter with PES-membrane
1 volumetric ultrapure water dispenser
1 disinfection connection with quick fit couplers.
1 single dose of disinfection solution
1 connection kit, including 2m tube
Control:
Graphical and programmable 7''-touch-glass panel to display:
- flow diagram for quality parameter monitoring
- pure water conductivity after the pre-treatment module DTO
- conductivity/resistivity of the ultrapure water
- conductivity of TOC sample measurements, 1-10 ppb measurement range
- ultrapure water temperature (temperature compensation can be disabled according to USP)
- servicing and consumable replacement requirements
- notification of system malfunction and/or quality issues
- settings monitoring
- 24-hour interval setting, prolonging pump and UV-lamp lifespan
- time program for automatic rinsing of the ultrafiltration module
- adjustable data backup to store conductivity, tank volume, pressure, and temperature data
- USB connection for data analysis
- micro-SD card for data backup (detachable)
- language options: German, English, French, Spanish, Portuguese and Chinese
- Managing entire unit using the control panel
- semi-automatic, menu selectable, disinfection of all water carrying parts
- setting of conductivity and temperature limits
- automatic disposal of recirculating water when the preset temperature limit is exceeded
- part number and consumables description within the control panel
- Easy cartridge replacement with user friendly connections
- cartridges with extended life-time
- Interface to connect POS printer or ModBus TCP/IP Data Communication Gateway to transfer the system status information to Building Management System (BMS)
The ultrapure laboratory water system is ready for use incl. the first set of modules and filters.
Technical data:
Ultrapure water specifications:
Volume flow rate: up to 2,0 l/min
Conductivity: 0.055 µS/cm
Resistivity: 18.2 MOhm-cm
TOC: < 1-5 ppb
Bacteria: < 1 CFU/ml
Silicate : < 1 ppb
Particulates > 0.1 µm/ml: < 1
Feed water requirements:
Pressure: 0.1 - 5 bar
Feed Water Flow rate: 60-120 l/h
Conductivity: < 20 µS/cm
Free chlroine: < 0,1mg/l
TOC: < 50 ppb
CO2: < 15 mg/l
SiO2: < 10 mg/l
Temperature: 5 - 35ºC
Mains input: 100-240 V, 50-60 Hz
Power consumption: 0,225 kW
Noise pressure level: max. 55 dB
Electrical connection cable
(D, GB, US): 2 m
Water connection: 1/2'' or 3/4'' female thread
Drain tube: 1/4''
Dimensions and Weight:
Width: 340 mm
Height: 535 mm
Depth: 550 mm
Dispatch weight: 26 kg
Key features
- Technical Information Sheet:
Recently viewed
You may also like
Questions about Ultra Clear TP ED UV TM
What is this article?
Ultra Clear TP ED UV TM is the article on this page. Luminix Health distributes Evoqua Water Technologies for laboratory use. It sits in Ultrapure & pure water systems, inside Water purification, in Lab instruments.
A pure-water system, often by reverse osmosis and deionisation, feeds the laboratory. An ultrapure polisher takes that water to the resistivity and organic levels HPLC or cell culture ask for. Production rate and the feed water it expects are the specification. The system is not a cooler.
Laboratory water is a reagent. Tap water carries ions, organics and microbes that become part of every result they touch. A pure-water system takes most of them out. An ultrapure system, often a polisher after a first stage, is what HPLC, cell culture and trace analysis ask for. Resistivity, total organic carbon and endotoxin are different claims. A cartridge is spent when the number drifts, not when the calendar says so. The measurement of those impurities sits with NIST and the BIPM.
Which category should I open next?
The category is Water purification. The sub-category is Ultrapure & pure water systems. The catalogue is Lab instruments.
Shelves beside this one are Water purification cartridges & consumables.
What should I check before I order?
When this page shows a safety data sheet, use that manufacturer file. Hazard text does not belong in the sales description. For a pack size, a grade or a certificate that is not on the page, send a quote request or contact the team.
How does ordering and shipping work?
Luminix Health distributes this article from the heart of Europe. Articles in stock ship within 2–5 business days. Standard delivery is free from €250 excl. VAT. Cold-chain goods and dangerous goods under ADR are never included in that free delivery. The terms are in the Shipping Policy. The full brand index is on shop by brand. Who we are is on about us.
Which other categories should I open?
The seven catalogues are Labware, Lab chemicals, Lab instruments, Lab consumables, Chromatography equipment, Lab safety equipment and Life Science & Microbiology.