Protegra CS PRO RO EDI 750
Reverse Osmosis with Ionpure EDI, 750 l/h

CONSISTENTLY HIGH WATER QUALITY

The Protegra CS® Pro RO EDI system is a high-performance purification solution for deionised water applications. Featuring industry-leading reverse osmosis technology and a high-performance Ionpure® CEDI cell, the system maintains water quality at the required standard.
The system is ideal for a range of laboratory and industrial applications with a typical water quality of > 0,07µS/cm and flow rates up to 750 l/h at 15°C.

Product features and benefits:
- Energy efficient and high performance reverse osmosis (RO) modules effectively achieve high inorganic retention and permeate production. This reduces energy demand and minimizes water waste.
- Electro-deionization removes the residual salt content from the water without exhausting itself.
- Automatic rinsing of entire system before going into stand-by mode reduces build-up of ions in the RO membranes - increasing the lifespan.
- Microprocessor control provides automatic operation with continuous monitoring of all important parameters.
- The limits for conductivity and flow rates of pure water can be set individually.
- Removable front and side panels for easy service access
- The system is low maintenance.

Production of pure water: Reverse osmosis
- Feed water solenoid valve
- Pressure regulator
- Conductivity sensor for feed water (cell constant C=0,1)
- 10'' 5µm foamed polypropylene depth filter
- Pressure switch for feed water
- Stainless steel pump (1.4401/1.4301)
- Pressure sensor for operating pressure
- 4 Reverse osmosis modules made of polyamide/polysulfone with pressure tubes made of stainless steel (1.4571) and end caps made of polypropylene (PP)
- Regulator for concentrate flow to drain and return
- Three flow sensors for pure water, concentrate and brine
- Conductivity sensor for permeate (cell constant C=0,2)
- Quality-dependent permeate distribution valve

Continuous Electrodeionization (CEDI):
- Ionpure CEDI module for up to 750 l/h
- Conductivity sensor for pure water, temperature compensated (cell constant C=0,1)
- Temperature sensor

New 7'' touch-panel control:
- Mounted on the front of the system
- System status displayed
- Conductivity of feed water, permeate and pure water
- Volume flow rate of pure water, concentrate and brine
- Alarm indicator
- Timeline for concentrate discharge to drain and module rinsing
- Multilingual (German, English)
- USB interface for data transfer
- microSD-Port (Data recording and firmware updates)

Supplied with:
- Operating manual
- Electrical circuit diagram
- Fine filter cartridge 5µm Big Blue
- key for filter cartridge
- Power cable NOT included

Optional:
- Water guard 1'' (W2T808003)
- LED-Signal light tower (Red-yellow-green) (W3T307039)
- Communication interface (Modbus gateway) for continuous data transfer to a BMS (Building management system) or PC/ laptop (W3T570885)
- Membrane degassing (W3T262426)
- Complete DQ/IQ/OQ/PQ documentation and validation of the system on site available upon request.

Feed water specifications:
Softened or hardness stabilized

Flow rate: 1100 - 1500 l/h
Pressure: 2,5 - 6,0 bar
Temperature: 5 - 30°C
Conductivity: < 1400 µS/cm
Colloid index (SDI): < 3
TDS: 700 mg/l
CO2: < 10 mg/l
SiO2: < 10 mg/l
TOC: < 1500ppb
pH: 3-9
Total iron: < 0,1 mg/l
Free chlorine: < 0,1 mg/l
Manganese: <0,05 mg/l

Performance specifications:
Flow rate at 15 °C: 750 l/h
Conductivity: < 0,1 µS/ml
Typical conductivity: < 0,07 µS/cm
Recovery rate up to: 50-80%

Technical data:
Mains input: 400V 3/N/PE 50/60 Hz
Power consumption: 3,0 kW/h
Ambient temperature: 1 - 30°C
Humidity: no condensation
Fuse protection: max. 16 A
Residual current device (RCD formerly FI):
Type B, 30mA, short-time delayed
Sound pressure level: max. 64db(a)

The power connection is made via supply terminals inside the Protegra and must be provided by the customer.

Hydraulic ports:
Feed water: G1.25'' MPT, d25 SOC
Product water: G1'' MPT, d20 SOC
Concentrate: G1'' MPT, d20 SOC
Brine: G3/4'' MPT

Dimensions and weight:
Height: approx. 1795 mm (fixed stand)
Height w/ optional lamp: 1960 mm
Width: 650 mm
Depth: 665 mm
Weight: approx. 275 kg

Please note:
The unit accepts a feed water salt concentration of 700 mg/l, equivalent to a conductivity of 1400 µS/cm at 15°C.
The feed water specifications are guidelines. The pure water specifications can only be guaranteed if a feed water analysis including levels of silicate and CO2 of the installation
site and all other relevant parameters have been analyzed.